Table of Content
Granite is naturally heat resistant, and heat damage would occur only if the granite was heated unevenly. Hold a point chisel at a 55-degree angle at one end of the granite. Strike the chisel just hard enough that the point goes no more than 1/2 inch into the surface.

Gerber has over four years of experience running GO Masonry and over ten years of general masonry work experience. He earned a BA in Marketing from the University of Mary Washington in 2017. Between the options, a straightedge is preferred because it can keep your line more even when you're ready to mark it. Position the tape measure or straightedge slightly to the left of the line you want so you can mark the line with tape later. Check the saw for the correct blade before cutting the granite.
How do you cut a hole in granite?
She specializes in residential remodels, boutique hospitality design, project management, and budget design. Emma holds a BA in Communication and Media Studies from Northeastern University and an MA in Interior Architecture from The New England School of Art and Design. She has a combined ten years of project management experience in the design, marketing, and non-profit industries, both nationally and internationally. If you don’t have a GFCI outlet available, use the dry-cut method instead to eliminate the risk of shock.
Make sure you have fitted your saw with a diamond-cut blade in the right size. The wrong size or type of blade can damage your saw and potentially result in injury. To protect your counters and your knives, avoid chopping vegetables and butchering meat directly on the surface of your granite. Instead, protect the surface with a large cutting board Always keep knives inside of a protective knife block, and tell family members to keep other cutlery put away. With a 3 1/4-inch diamond-grit blade, you can cut through porcelain, tile, slate, limestone and even granite tiles, provided that the tiles are not thicker than 1/2 inch.
Can circular saw cut stone?
It is impossible to predict the rate at which bonds will wear out based on their density. When cutting very dense concrete, the softer bond is preferred. If you use a blade that isn’t the appropriate size, your grinder or saw will be inefficient at cutting. The rate at which blades are spun is determined by the blade design.
Although you can use the saw with one hand, you should use two hands to be careful. After measuring out where you will make the cut, apply the strip of painter’s tape to the area where you will be cutting. After you do this, draw a straight line on the tape while using the ruler or tape measure as a guide . This line is so important because it will serve as a visual aid while cutting, so you must be very careful when marking. Peel the tape from the granite and admire your smooth, clean cut.
What is the best tool to cut stone?
You will use the marker to draw a straight line on the painter’s tape to help create a visual guide as you are cutting. You do not want to breathe in any of the dust that may be produced while you are cutting. Turn the saw off before removing cut pieces of granite tile from the sliding table.

Although it can cost $300 to $500 to cut this stone, installers include granite fabrication services in their labor rate. They will trim it to size, round or bevel the edges, and cut out the sink, for example, during the install. It really depends on what type of look, functionality and maintenance you are looking for in your countertops. Both quartz and granite countertops offer a beautiful and durable surface. As an example, some experienced professionals may add in the cost of an exotic diamond-tip bit for the most intricate of cuts when cutting a particular kind of granite. All these various expenses can add up, making the cost of cutting granite quite high.
Redo the cut with the angle grinder until the hole is wide and consistent. Cut through the center of the hole to the edges of the outline for the rounded corners. After you’ve made the initial cut, it’s easy to complete the rest of the work.
In higher-end quartz options, the price may exceed that of granite. In addition, the cost of installation may also vary depending on the amount of labor required and the type of edge you choose. When comparing the cost of quartz and granite, it is important to consider the quality of each stone and any additional costs that may be involved. If the tools used are not sharp enough or the right kind of saw and cutting techniques are not followed, granite can crack when being cut. Additionally, stresses created during and after cutting can also cause the granite to crack. You must first mark the outline of the hole and then place the point of the drill bit against the exterior of the stone.
A technician will outfit the kitchen with plastic tarps to form a reliable dust tent. They will then take measurements and mark off the areas to cut with tape. Granite countertop installers and repairers have the tools and knowledge to make tricky cuts and finish the edges of your countertop in tight spaces. You can also rely on them to set up a dust tent and take other necessary safety precautions.
Apply an even pressure as you drill into the granite and keep the bit straight and centered. All in all, cutting through granite requires specialized tools, knowledge of the process, and significant time and effort. You will need an angle grinder to smooth any edges after you cut the granite.
Just remember that repeatedly placing a very hot pan on the same spot may cause granite to discolor. Overall, both quartz and granite countertops offer a variety of benefits and can give you the look and durability you are looking for. It really depends on which one better suits your needs, preferences and budget. Granite is a natural stone, mined directly from the earth. It is extremely durable and is available in a wide variety of color, patterns and finishes. Since it is more porous than quartz, it is more difficult to maintain and can require sealing over time.
Instead of pushing the saw forward with force, hold onto it with a light amount of pressure. Guide it gradually over the lines to get perfect, smooth cuts. For the rounded corners, cut from the center of the hole to the edges of the outline.
No comments:
Post a Comment